Автор: tasiya

Очень люблю живой огонь! Но дома это сложно организовать.
Посмотрите на простую идею как можно это сделать.
Понадобится: металлическая миска, камни, стакан и био-топливо для камина или просто свечки.
Мы делали многоэтажный, с гротами. Но в тот момент в доме не было электричества, поэтому пока идея простого, а позже мы покажем и большой. Попробуйте, это просто и красиво! И показывайте, что у вас получилось. Уверена, что много хороших идей подскажете!:)

Download the basket weaving template (consist of triangle, round and square) in pdf format.
{It will either open in new tab or open a small window asking you to save it as file. If you can’t find the saved file in your computer, the default folder usually is in “/downloads”}
{If you can’t download the pdf pattern, probably you don’t have acrobat reader, download the latest version for free, here.}
Print it and enlarge 200% to get the size I made.
Trace it on the thick cardboard.
After tracing the template on the thick cardboard, use a pair of strong and sharp scissors to cut the template out.
Punch the holes with a paper hole-puncher.
Trace base on felt, cut 2 pieces.
Get the rest of the tools & materials ready.
Brush a layer of tacky glue on the bottom of the basket, press & stick the felt onto it.
Repeat the same to adhere the felt to the base.
Snip the edge of the felt follows the grooves between the fingers.
Being to weave over and under around the fingers of the frame.
Push the twine into the grooves of the felt that you have just snipped.
Keep on weaving over and under the fingers until the end of first round.
When begin the second round, you will notice that you are weaving in the reverse side of the first round.
A full wrap on both sides after finish the second round.
Continue weaving and push the twine down to make them closer to each other. This will avoid gaps in between and will also hide the cardboard away.
As you go higher, the frame will stand up vertically and form the side of the basket.
Continue until you just over the hole’s level.
Allow a long length of twine for rim stitching later.
Put on clothes pin and allow some room for rim making.
To make the rim, insert another type of twine through the space between the clothes pin by using a tapestry needle.
Since the length is quite long, divide the twine by halve and work both ends from middle.
Keep going round by round. Take note on the corners and arrange them neatly.
Lay the twine until it fully covers the top portion of the basket.
Secure the rim by stitching the original twine through the holes.
Stitch again on the opposite direction to form criss-cross pattern.
When reaching the corner, pierce through the gap and make another stitch there.
Hide all ends into the braid to neaten up the basket.
The basket is ready to be used.

3 basic materials to work on, the manila rope, yarn or twine and a crochet hook.

Crochet basic round according to the pattern (R1).

On round 2 onwards, all single crochet (sc) stitches in the pattern means single crochet on the rope.
Place the yarn under the rope.

Insert hook into the loops of the previous round’s stitch, yarn over (yo) the yarn from the top of the rope.

Pass through the loops of the previous round’s stitches to complete the sc around the rope.

Crochet the base follow the pattern above. This is the 2nd round, remember to place a marker so you will know where is the beginning stitch of the round.

Third round. Adjust the rope end nicely and fit into the base.
Crochet the rest as per pattern above.

The look of the basket from the bottom.

Complete till Round 24, just before making handles on the final 2 rounds.

You will see the increment stitch as this, sc on next ch st, ch1, sc on same ch st, ch1.

Round 25, handle construction. The handle is 6″ but if you want longer handle, you can always adapt to your length.

Round 26, wind and twist the rope on the handle.

This is the 3 sc stitches before and after the handle.

Apply the glue at the rope end, clip it to the basket until it is dry and securely fastened.

Сделаем сами тычинки для цветов... МК

Всем - привет!!! Девочки, кто учавствовал в закупке- меня поймут.. сложно найти тычинки нужного цвета и нужного количества Ну так сделаем сами!
Я для основы взяла пряжу Ажурная- толщна подошла идеально
С помощью иглы прокалываю пузыречек клея ( ПВА )

Пузырек перевернуть, чтобы внутри ниточка проходила через клей. Можно натянуть на коробку или на что-то другое. Сохнет очень быстро, наверное минут 15-20


Потом нарезаю на "палочки". Я сравнила с фабричным тычинками- 7 см. Готовим смесь для головок- крахмал и ПВА ( как густая сметана)


Можно сразу добавить туда краску акриловую или гуашь, но я решила красить потом
первый слой ( первый нырок тычинок в клей)

можно нырнуть еще разок ( сохнет тоже быстро, минут 15)



теперь можно покрасить, можно использовать беленькими


http://www.stranamam.ru/post/3536593/